The Jeff Rowland Model 7 is one of those amplifiers from the mid-1980s high-end that people are still chasing today — massive, beautifully machined monoblocks built to tame near-zero-impedance loads without surrendering an ounce of musical finesse. The presentation is archetypal Rowland: warm, unhurried, and effortlessly authoritative, with a midrange bloom and a sweetness through the top end that most solid-state amps of this scale couldn't get near. Bass is deep and controlled without being aggressive; imaging is generous and three-dimensional; and there's a sense of ease to the whole picture that belies just how much hardware is working underneath. They made their debut at CES 1985 driving Dave Wilson's WAMM system, and the legend started right there.
Production
1984-1992
Condition
Cosmetic 8/10 - Electronic 10/10
Serial No.
007 / 013
Orig. MSRP
$4,900
Restoration
- Cleaned power switch contacts
- Repainted chassis covers
- Both units perform at factory spec
Factory Specs
Power Output 350W RMS continuous (8Ω); 700W RMS continuous (4Ω); 1100W RMS continuous (2Ω)
Output Current 50A peak continuous; 150A peak at 0.1Ω, 20 msec, 1 kHz
Power Bandwidth 0.15 Hz to 175 kHz, -3 dB
Slew Rate 50 V/µs
THD and Noise Less than 0.015% (20W); less than 0.045% (100W); less than 0.06% (200W) — all 1 kHz, 8Ω
Damping Factor (specified) Greater than 300 (20 Hz–20 kHz, 8Ω); greater than 90 (100 kHz, 8Ω)
Damping Factor (guaranteed minimum) Greater than 120 (20 Hz–20 kHz, 8Ω); greater than 80 (100 kHz, 8Ω)
Common-Mode Rejection Ratio Greater than 90 dB, 20 Hz to 20 kHz
Overall Gain 26.4 dB (selectable: 20, 26, 29.5, or 32 dB; factory default: 26 dB)
Sensitivity 136 mV for 1W into 8Ω
Input Impedance Selectable: 100kΩ (low), 20kΩ (medium, factory default), or 600Ω (high)
Amplifier Class Class A/AB composite sliding bias (pure Class A at low levels, Class AB at higher output)
Signal Path Fully DC-coupled; no capacitors, inductors, fuses, or protection circuits in signal path
Input Stage Single-stage FET voltage amplification (transconductance mode)
Output Stage High-speed bipolar transistors, individually matched; no global or nested negative feedback; no electronic protection circuitry
Circuit Encapsulation All critical circuitry potted in thermally-conductive epoxy
Power Requirements 100V–240V AC, user-selectable; 50/60 Hz
Power Consumption at Idle 300W
Power Consumption in Standby Less than 25W
Power Supply Transformer 2kVA custom toroidal
Power Supply Capacitance 132,000 µF total (six 22,000 µF / 100V filter capacitors)
Dimensions 19 × 8.75 × 24 in. (W × H × D)
Weight 141 lbs (64 kg) per monoblock each
Documentation
Jeff Rowland Model 7 Owner's Manual
Liner Notes
Congratulations on your purchase of the Jeff Rowland Design Group Model 7 Mono amplifier. The Model 7 offers tremendous interconnection flexibility regardless of the preamp used. A thorough understanding of your amplifier now can save you a lot of anxiety later.
Lack of overall or nested negative feedback eliminates time domain distortion. Proprietary distortion canceling techniques minimize amplitude related distortions. Each transistor individually tested and matched for optimum operating characteristics. Constant output impedance is maintained over the entire audio range, allowing for universal compatibility with associated equipment. The large number of high-speed bipolar output transistors provides uncompromising reliability and eliminates the need for electronic protection circuitry. A single voltage amplification stage utilizes field effect transistors (operating in transconductance mode), which increases low-level signal recognition. The absence of capacitors, inductors, fuses and protection circuitry throughout the signal path eliminates the adverse effects of these devices. A specially designed toroidal power transformer is supported by the substantial output stage capability. All critical circuitry is encapsulated in a thermally-conductive epoxy to ensure excellent thermal stability, mechanical integrity and to facilitate ease of service.
Shipping
To ensure safe arrival, we often use private couriers. These are transporters in Sprinter Vans or pulling covered trailers often moving art and antiques across the country. Absolutely the safest way to ship short of you picking it up yourself. This piece ships to the contiguous United States for a flat rate of $500, which includes our packaging and our insurance. Of course, we'll ship anywhere in the world, just drop us a line and we'll give you an estimate – even if you're just curious.
Stock No.
15521101119709